收藏本站
...the world's most energy friendly microcontrollers
synchronization, the write operation requires 3 positive edges of the clock of the Low Energy Peripheral
being accessed. Such registers are marked "Asynchronous" in their description header.
See Figure 5.3 (p. 19) for an overview of the writing operation.
After writing data to a register which value is to be synchronized into the Low Energy clock domain, a
corresponding busy flag in the <module_name>_SYNCBUSY register (e.g. RTC_SYNCBUSY) is set.
This flag is set as long as synchronization is in progress and is cleared upon completion.
Note
Subsequent writes to the same register before the corresponding busy flag is cleared is not
supported. Write before the busy flag is cleared may result in undefined behavior.
In general the SYNCBUSY register only needs to be observed if there is a risk of multiple
write access to a register (which must be prevented). It is not required to wait until the
relevant flag in the SYNCBUSY register is cleared after writing a register. E.g can EM2 be
entered directly after writing a register.
Figure 5.3. Write operation to Low Energy Peripherals
Core Clock Dom ain
Low Frequency Clock Dom ain
Core Clock
Register 0
Register 1
.
.
.
Register n
Freeze
Low Frequency Clock
Synchronizer 0
Synchronizer 1
.
.
.
Synchronizer n
Low Frequency Clock
Register 0 Sync
Register 1 Sync
.
.
.
Register n Sync
Synchronization Done
Write[ 0:n]
Set 0
Set 1
Set n
Syncbusy Register 0
Syncbusy Register 1
.
.
.
Syncbusy Register n
Clear 0
Clear 1
Clear n
5.3.1.2 Reading
When reading from a Low Energy Peripheral, the data read is synchronized regardless if it originates
in the Low Energy clock domain or core clock domain. Registers which are updated/ maintained by the
Low Energy Peripheral are read directly from the Low Energy clock domain. Registers which originate in
the core clock domain, are read from the core clock domain. See Figure 5.4 (p. 20) for an overview
of the reading operation.
Note
Writing a register and then immediately reading the new value of the register may give the
impression that the write operation is complete. This may not be the case. Please refer
to the SYNCBUSY register for correct status of the write operation to the Low Energy
Peripheral.
2011-04-12 - d0001_Rev1.10
19
www.energymicro.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EFM32GG-STK3700 KIT STARTER GIANT GECKO
EFM32LG-DK3650 KIT DEV EFM32 LEOPARD GECKO
EK-K7-KC705-CES-G-J KINTEX-7 FPGA KC705 EVAL KIT
EK-S6-SP601-G KIT EVAL SPARTAN 6 SP601
EK-S6-SP605-G KIT EVAL SPARTAN 6 SP605
EK-V6-ML631-G-J VIRTEX-6 HXT FPGA ML631 EVAL KIT
EK-V7-VC707-CES-G VIRTEX-7 VC707 EVAL KIT
EK-Z7-ZC702-CES-G ZYNQ-7000 EPP ZC702 EVAL KIT
相关代理商/技术参数
EFM32GG230F1024 功能描述:ARM微控制器 - MCU 1024KB FL 128KB RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
EFM32GG230F1024G-E-QFN64R 功能描述:IC MCU 32BIT 1MB FLASH 64QFN 制造商:silicon labs 系列:Giant Gecko 包装:剪切带（CT） 零件状态:在售 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:48MHz 连接性:I2C，IrDA，智能卡，SPI，UART/USART 外设:欠压检测/复位，DMA，POR，PWM，WDT I/O 数:56 程序存储容量:1MB（1M x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:128K x 8 电压 - 电源（Vcc/Vdd）:1.98 V ~ 3.8 V 数据转换器:A/D 8x12b，D/A 2x12b 振荡器类型:内部 工作温度:-40°C ~ 85°C（TA） 封装/外壳:64-VFQFN 裸露焊盘 供应商器件封装:64-QFN（9x9） 标准包装:1
EFM32GG230F1024-QFN64 制造商:Energy Micro AS 功能描述:GIANT GECKO MCU - Cut TR (SOS) 制造商:Energy Micro 功能描述:GIANT GECKO MCU 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 1MB FLASH 64QFN
EFM32GG230F1024-QFN64T 制造商:Energy Micro AS 功能描述:GIANT GECKO MCU - Trays
EFM32GG230F1024-QFN64-T 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 1MB FLASH 64QFN
EFM32-GG230F1024-SK 制造商:Energy Micro AS 功能描述:GIANT GECKO SAMPLE KIT - Bulk
EFM32GG230F1024-T 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 1MB FLASH 64QFN
EFM32GG230F512 功能描述:ARM微控制器 - MCU 512KB FL 128KB RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
    • 我
    • 采购
    • 搜索
    • 会员